diff --git a/arch/arm/include/asm/arch-am33xx/clock.h b/arch/arm/include/asm/arch-am33xx/clock.h
index 9dbcd3a..eeebf16 100644
--- a/arch/arm/include/asm/arch-am33xx/clock.h
+++ b/arch/arm/include/asm/arch-am33xx/clock.h
@@ -122,6 +122,12 @@
 void do_setup_dpll(const struct dpll_regs *, const struct dpll_params *);
 void prcm_init(void);
 void enable_basic_clocks(void);
+
+void rtc_only_update_board_type(u32 btype);
+u32 rtc_only_get_board_type(void);
+void rtc_only_prcm_init(void);
+void rtc_only_enable_basic_clocks(void);
+
 void do_enable_clocks(u32 *const *, u32 *const *, u8);
 void do_disable_clocks(u32 *const *, u32 *const *, u8);
 
diff --git a/arch/arm/mach-omap2/am33xx/Kconfig b/arch/arm/mach-omap2/am33xx/Kconfig
index 9a9ccd7..76da6d9 100644
--- a/arch/arm/mach-omap2/am33xx/Kconfig
+++ b/arch/arm/mach-omap2/am33xx/Kconfig
@@ -239,6 +239,20 @@
 
 endchoice
 
+config SPL_RTC_DDR_SUPPORT
+	bool
+	depends on SPL
+	prompt "Enable RTC-DDR ONLY Support"
+	help
+	  If you want RTC-DDR ONLY Support, say Y. RTC Only with DDR in
+	  self-refresh mode is a special power saving mode where in all
+	  the other voltages are turned off apart from the RTC domain and DDR.
+	  So only RTC is alive and ticking and one can program it to wake
+	  up after a predetermined period. Once RTC alarm fires, the PMIC
+	  powers up all the voltage domains. U-Boot takes a special path
+	  as the DDR has contents is in self-refresh and restore path is
+	  followed.
+
 endif
 
 if AM43XX || AM33XX
diff --git a/arch/arm/mach-omap2/am33xx/board.c b/arch/arm/mach-omap2/am33xx/board.c
index ea0caba..ef1de1a 100644
--- a/arch/arm/mach-omap2/am33xx/board.c
+++ b/arch/arm/mach-omap2/am33xx/board.c
@@ -147,6 +147,16 @@
 }
 #endif
 
+/*
+ * RTC only with DDR in self-refresh mode magic value, checked against during
+ * boot to see if we have a valid config. This should be in sync with the value
+ * that will be in drivers/soc/ti/pm33xx.c.
+ */
+#define RTC_MAGIC_VAL		0x8cd0
+
+/* Board type field bit shift for RTC only with DDR in self-refresh mode */
+#define RTC_BOARD_TYPE_SHIFT	16
+
 /* AM33XX has two MUSB controllers which can be host or gadget */
 #if (defined(CONFIG_USB_MUSB_GADGET) || defined(CONFIG_USB_MUSB_HOST)) && \
 	(defined(CONFIG_AM335X_USB0) || defined(CONFIG_AM335X_USB1)) && \
@@ -252,6 +262,48 @@
 #endif /* CONFIG_USB_MUSB_* && CONFIG_AM335X_USB* && !CONFIG_DM_USB */
 
 #ifndef CONFIG_SKIP_LOWLEVEL_INIT
+
+#if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC) || \
+	(defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_RTC_DDR_SUPPORT))
+static void rtc32k_unlock(struct davinci_rtc *rtc)
+{
+	/*
+	 * Unlock the RTC's registers.  For more details please see the
+	 * RTC_SS section of the TRM.  In order to unlock we need to
+	 * write these specific values (keys) in this order.
+	 */
+	writel(RTC_KICK0R_WE, &rtc->kick0r);
+	writel(RTC_KICK1R_WE, &rtc->kick1r);
+}
+#endif
+
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_RTC_DDR_SUPPORT)
+/*
+ * Write contents of the RTC_SCRATCH1 register based on board type
+ * Two things are passed
+ * on. First 16 bits (0:15) are written with RTC_MAGIC value. Once the
+ * control gets to kernel, kernel reads the scratchpad register and gets to
+ * know that bootloader has rtc_only support.
+ *
+ * Second important thing is the board type  (16:31). This is needed in the
+ * rtc_only boot where in we want to avoid costly i2c reads to eeprom to
+ * identify the board type and we go ahead and copy the board strings to
+ * am43xx_board_name.
+ */
+void update_rtc_magic(void)
+{
+	struct davinci_rtc *rtc = (struct davinci_rtc *)RTC_BASE;
+	u32 magic = RTC_MAGIC_VAL;
+
+	magic |= (rtc_only_get_board_type() << RTC_BOARD_TYPE_SHIFT);
+
+	rtc32k_unlock(rtc);
+
+	/* write magic */
+	writel(magic, &rtc->scratch1);
+}
+#endif
+
 /*
  * In the case of non-SPL based booting we'll want to call these
  * functions a tiny bit later as it will require gd to be set and cleared
@@ -261,7 +313,9 @@
 {
 	prcm_init();
 	set_mux_conf_regs();
-
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_RTC_DDR_SUPPORT)
+	update_rtc_magic();
+#endif
 	return 0;
 }
 
@@ -278,13 +332,7 @@
 {
 	struct davinci_rtc *rtc = (struct davinci_rtc *)RTC_BASE;
 
-	/*
-	 * Unlock the RTC's registers.  For more details please see the
-	 * RTC_SS section of the TRM.  In order to unlock we need to
-	 * write these specific values (keys) in this order.
-	 */
-	writel(RTC_KICK0R_WE, &rtc->kick0r);
-	writel(RTC_KICK1R_WE, &rtc->kick1r);
+	rtc32k_unlock(rtc);
 
 	/* Enable the RTC 32K OSC by setting bits 3 and 6. */
 	writel((1 << 3) | (1 << 6), &rtc->osc);
@@ -321,8 +369,54 @@
 		;
 }
 
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_RTC_DDR_SUPPORT)
+/*
+ * Check if we are executing rtc-only + DDR mode, and resume from it if needed
+ */
+static void rtc_only(void)
+{
+	struct davinci_rtc *rtc = (struct davinci_rtc *)RTC_BASE;
+	u32 scratch1;
+	void (*resume_func)(void);
+
+	scratch1 = readl(&rtc->scratch1);
+
+	/*
+	 * Check RTC scratch against RTC_MAGIC_VAL, RTC_MAGIC_VAL is only
+	 * written to this register when we want to wake up from RTC only
+	 * with DDR in self-refresh mode. Contents of the RTC_SCRATCH1:
+	 * bits 0-15:  RTC_MAGIC_VAL
+	 * bits 16-31: board type (needed for sdram_init)
+	 */
+	if ((scratch1 & 0xffff) != RTC_MAGIC_VAL)
+		return;
+
+	rtc32k_unlock(rtc);
+
+	/* Clear RTC magic */
+	writel(0, &rtc->scratch1);
+
+	/*
+	 * Update board type based on value stored on RTC_SCRATCH1, this
+	 * is done so that we don't need to read the board type from eeprom
+	 * over i2c bus which is expensive
+	 */
+	rtc_only_update_board_type(scratch1 >> RTC_BOARD_TYPE_SHIFT);
+
+	rtc_only_prcm_init();
+	sdram_init();
+
+	resume_func = (void *)readl(&rtc->scratch0);
+	if (resume_func)
+		resume_func();
+}
+#endif
+
 void s_init(void)
 {
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_RTC_DDR_SUPPORT)
+	rtc_only();
+#endif
 }
 
 void early_system_init(void)
diff --git a/arch/arm/mach-omap2/am33xx/clock.c b/arch/arm/mach-omap2/am33xx/clock.c
index 3d17698..ad28d20 100644
--- a/arch/arm/mach-omap2/am33xx/clock.c
+++ b/arch/arm/mach-omap2/am33xx/clock.c
@@ -244,3 +244,13 @@
 	scale_vcores();
 	setup_dplls();
 }
+
+void rtc_only_prcm_init(void)
+{
+	const struct dpll_params *params;
+
+	rtc_only_enable_basic_clocks();
+
+	params = get_dpll_ddr_params();
+	do_setup_dpll(&dpll_ddr_regs, params);
+}
diff --git a/arch/arm/mach-omap2/am33xx/clock_am43xx.c b/arch/arm/mach-omap2/am33xx/clock_am43xx.c
index 73ea955..117a63e 100644
--- a/arch/arm/mach-omap2/am33xx/clock_am43xx.c
+++ b/arch/arm/mach-omap2/am33xx/clock_am43xx.c
@@ -124,6 +124,27 @@
 	writel(0x4, &cmdpll->clkselmacclk);
 }
 
+void rtc_only_enable_basic_clocks(void)
+{
+	u32 *const clk_domains[] = {
+		&cmper->emifclkstctrl,
+		0
+	};
+
+	u32 *const clk_modules_explicit_en[] = {
+		&cmper->gpio5clkctrl,
+		&cmper->emiffwclkctrl,
+		&cmper->emifclkctrl,
+		&cmper->otfaemifclkctrl,
+		0
+	};
+
+	do_enable_clocks(clk_domains, clk_modules_explicit_en, 1);
+
+	/* Select the Master osc clk as Timer2 clock source */
+	writel(0x1, &cmdpll->clktimer2clk);
+}
+
 #ifdef CONFIG_TI_EDMA3
 void enable_edma3_clocks(void)
 {
diff --git a/board/ti/am43xx/MAINTAINERS b/board/ti/am43xx/MAINTAINERS
index 83645ac..bf09806 100644
--- a/board/ti/am43xx/MAINTAINERS
+++ b/board/ti/am43xx/MAINTAINERS
@@ -7,4 +7,5 @@
 F:	configs/am43xx_evm_ethboot_defconfig
 F:	configs/am43xx_evm_qspiboot_defconfig
 F:	configs/am43xx_evm_usbhost_boot_defconfig
+F:	configs/am43xx_evm_rtconly_defconfig
 F:	configs/am43xx_hs_evm_defconfig
diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c
index 715960a..d8944ea 100644
--- a/board/ti/am43xx/board.c
+++ b/board/ti/am43xx/board.c
@@ -520,6 +520,62 @@
 	writel(temp, AM33XX_GPIO5_BASE + OMAP_GPIO_OE);
 }
 
+enum {
+	RTC_BOARD_EPOS = 1,
+	RTC_BOARD_EVM14,
+	RTC_BOARD_EVM12,
+	RTC_BOARD_GPEVM,
+	RTC_BOARD_SK,
+};
+
+/*
+ * In the rtc_only+DRR in self-refresh boot path we have the board type info
+ * in the rtc scratch pad register hence we bypass the costly i2c reads to
+ * eeprom and directly programthe board name string
+ */
+void rtc_only_update_board_type(u32 btype)
+{
+	const char *name = "";
+	const char *rev = "1.0";
+
+	switch (btype) {
+	case RTC_BOARD_EPOS:
+		name = "AM43EPOS";
+		break;
+	case RTC_BOARD_EVM14:
+		name = "AM43__GP";
+		rev = "1.4";
+		break;
+	case RTC_BOARD_EVM12:
+		name = "AM43__GP";
+		rev = "1.2";
+		break;
+	case RTC_BOARD_GPEVM:
+		name = "AM43__GP";
+		break;
+	case RTC_BOARD_SK:
+		name = "AM43__SK";
+		break;
+	}
+	ti_i2c_eeprom_am_set(name, rev);
+}
+
+u32 rtc_only_get_board_type(void)
+{
+	if (board_is_eposevm())
+		return RTC_BOARD_EPOS;
+	else if (board_is_evm_14_or_later())
+		return RTC_BOARD_EVM14;
+	else if (board_is_evm_12_or_later())
+		return RTC_BOARD_EVM12;
+	else if (board_is_gpevm())
+		return RTC_BOARD_GPEVM;
+	else if (board_is_sk())
+		return RTC_BOARD_SK;
+
+	return 0;
+}
+
 void sdram_init(void)
 {
 	/*
diff --git a/configs/am43xx_evm_rtconly_defconfig b/configs/am43xx_evm_rtconly_defconfig
new file mode 100644
index 0000000..ab0be10
--- /dev/null
+++ b/configs/am43xx_evm_rtconly_defconfig
@@ -0,0 +1,59 @@
+CONFIG_ARM=y
+CONFIG_ARCH_OMAP2PLUS=y
+CONFIG_TI_COMMON_CMD_OPTIONS=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_AM43XX=y
+CONFIG_DEFAULT_DEVICE_TREE="am437x-gp-evm"
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=1"
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_SPL=y
+CONFIG_SPL_RTC_DDR_SUPPORT=y
+CONFIG_SPL_MTD_SUPPORT=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_CMD_SPL=y
+CONFIG_CMD_SPL_NAND_OFS=0x00100000
+CONFIG_CMD_SPL_WRITE_SIZE=0x40000
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_NAND=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=nand.0"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=nand.0:256k(NAND.SPL),256k(NAND.SPL.backup1),256k(NAND.SPL.backup2),256k(NAND.SPL.backup3),512k(NAND.u-boot-spl-os),1m(NAND.u-boot),256k(NAND.u-boot-env),256k(NAND.u-boot-env.backup1),7m(NAND.kernel),-(NAND.file-system)"
+CONFIG_OF_CONTROL=y
+CONFIG_OF_LIST="am437x-gp-evm am437x-sk-evm am43x-epos-evm am437x-idk-evm"
+CONFIG_DM=y
+# CONFIG_BLK is not set
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_SF=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_OMAP_HS=y
+CONFIG_NAND=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_GIGE=y
+CONFIG_DM_SERIAL=y
+CONFIG_SYS_NS16550=y
+CONFIG_TI_QSPI=y
+CONFIG_TIMER=y
+CONFIG_OMAP_TIMER=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GADGET=y
+CONFIG_USB_DWC3_OMAP=y
+CONFIG_USB_DWC3_PHY_OMAP=y
+CONFIG_OMAP_USB_PHY=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0403
+CONFIG_USB_GADGET_PRODUCT_NUM=0xbd00
+CONFIG_USB_GADGET_DOWNLOAD=y